Non-Slewing Mobile Crane Licence (Manitou, Genie, Franna)
Incremental payments may apply
Please contact us for upcoming course dates.
The Non-Slewing Crane Licence Course is designed for personnel who wish to operate a Non-Slewing Crane with a load capacity greater than 3 tonne. The course is competency based, and successful applicants who attain the necessary competence will be eligible to apply for the issue of a National Licence through the local Regulator or Worksafe Authority. Persons who hold this licence are permitted to operate non-slewing cranes of any capacity.
Throughout this course, students will learn how to safely and competently:
- Plan work involving a non-slewing crane, including identification and control of hazards.
- Carry out selection and inspection of cranes and associated equipment.
- Create a job plan, plan a lift and set up the work area appropriately.
- Set up the crane and the work area following manufacturer specifications, permit requirements, site procedures and regulations.
- Operate a non-slewing crane, mobile & transfer loads and carry out shut down procedures.
- Work in a way that meets Work Health & Safety (WHS) and other legal requirements.
This course may include some or all of the following delivery modes: classroom, online/eLearning, workplace or blended options.
Assessment is conducted using the mandated assessment tool set by the Regulator, which requires a reasonable command of English and basic numeracy skills.
You must be at least 18 years old to obtain a High Risk Work licence.
Students must be at least 18 years old to obtain this licence.
Assessment activities must all be conducted whilst communicating in English, and interpreters are not allowed to be used. Students require a reasonable command of English and basic numeracy skills to complete the government-mandated assessment tool for this course. Only minor adjustments for personal or workplace reasons are allowed.
Hearing impaired persons may use sign language to communicate via an interpreter (only when approved by the Regulator).
The course may involve some manual handling, climbing, lifting, carrying, and height work. It must be clearly understood that some disabilities may preclude a student from participating safely, and this may restrict entry to the course. For details and alternatives, please refer to AITAC administrator for advice.
While we will make every effort to cater to the specific needs of students, decisions relating to safety are not subject to negotiation.
This course may involve working in a warehouse, construction or outdoor environment, and performing High Risk Work. Students are therefore required to wear suitable Personal Protective Equipment (PPE) during training.
When attending the course, students must bring/wear:
- Fully enclosed shoes or boots (steel-capped safety shoes recommended)
- Drill shirt and pants (full cover – ankle to wrist)
We will provide hi-vis vests, books, pens, tools and other resources needed for the course.
Students who do not have the appropriate PPE will not be permitted to participate in the practical component of the course and may have to be rescheduled at another available time. This may incur additional fees (please refer to the Student Handbook for specific fee details).
Training which takes place in the workplace under supervision may require different or additional PPE dependent upon the site rules and procedures. If this is the case, requirements should be discussed with your employer/supervisor.
The duration of this course is 3 days. Study may also include pre-course learning activities.
The course is delivered at 9 Snyder Crt, Tullamarine VIC, or can be delivered at other suitable workplaces by arrangement.
On successful completion of this course, you will be issued with a nationally recognised Statement of Attainment with the relevant Units of Competency.
You will be able to apply for a nationally recognised High Risk Work Licence from a state regulator. During this process, you will be required to pay an additional government licensing fee of $50 – $100.
The standard price for this course is $1,800.00
Student tuition fees as published are subject to change given individual circumstances at enrolment and are inclusive. There are no other fees or charges.
* All prices are indicative and may change dependent on participant experience, number of applicants, locations etc. Please call to discuss accurate pricing for your circumstance. **For information about fees, refunds, transfers and other related information please click HERE
This course may qualify the applicant in competency units included below:
TLILIC3006 Licence to operate a non-slewing mobile crane (greater than 3 tonnes capacity)
TLIB3012 Plan job and set up work areas.
TLIF3084 Follow mobile crane safety procedures
RIIBEF201D Plan and organise work
RIIWHS201D Work safely and follow WHS policies and procedures
AITAC RTO (ID 3591) is responsible for quality of training and assessment, compliance with ASQA Standards for RTO’s, and the issuance of AQF Certification documentation (SOA and qualifications).
Business Booking or Enquiry Or call 03 9492 2988